Brad Nail
Virtually Invisible Holes. No More Ugly Wood Filler.
Drive Them Hard. No Splitting in Delicate Trim.
Holds Strong, Hides Completely. The Final Touch Done Right.
01
Your Trusted Factory Direct Source for Precision Brad Nails | Sinsun
As your professional brad nail manufacturer, Sinsun delivers flawless 18-Gauge nails for perfect trim work. Experience zero-jam performance and invisible finishes. Partner with your global supplier for consistent quality and reliable bulk supply
-
Save 80% on Filling Time
Sinsun's #18 nails create holes that are so small they are almost invisible. With a shank diameter of only 1.2 mm, they reduce wood filler usage by over 80% and eliminate sanding time. One of our German customers reported that the finishing work for each room was reduced by 2 hours by completely eliminating the filler and sanding steps.· Sinsun's #18 nails create holes that are so small they are almost invisible. With a shank diameter of only 1.2 mm, they reduce wood filler usage by over 80% and eliminate sanding time. One of our German customers reported that the finishing work for each room was reduced by 2 hours by completely eliminating the filler and sanding steps. -
Reduce Wood Cracking Risk by 90%
Our precise 0.084-inch diameter diamond-shaped nail tips penetrate wood fibers without causing cracking. Each nail is heat-treated to a hardness of 48-52 HRC—ensuring straight insertion while maintaining controllable flexibility. When using our nails to create intricate decorative moldings, material loss due to cracking is reduced by 90%. -
Guaranteed 99.8% Smooth Nail Insertion Rate
Our automated factory uses a precise 3-5 micron galvanizing process and laser-calibrated nailing machines. This ensures a 99.8% nail-free performance for all major nail gun brands. 50 rolls of nails were used consecutively without a single jam – equivalent to using over 15,000 nails consecutively. -
Save 15 minutes of work time per 1,000 nails
The perfectly aligned strip design speeds up nailing and enables continuous work. Contractors report saving approximately 15 minutes of work time per 1,000 nails using our precision-welded nail rolls. This translates to less time required to drive in 1,000 nails compared to standard brands. This means a saving of 2.5 hours in a typical interior decorating project – time that directly translates into your profits.
18 gauge brad nail
Send inquiry Now
stainless steel brad nails
Send inquiry Now
16 gauge brad nails
Send inquiry Now
finish nails
Send inquiry Now
black brad nails
Send inquiry Now
small brad nails
Send inquiry Now
23ga pin nails
Send inquiry Now
15 gauge nail
Send inquiry Now
angled nails
Send inquiry Now
F nails
Send inquiry Now01
Gauge |
Nail Length (in) |
Nail Length (mm) |
Shank Diameter (mm) |
Approx. Nails per Coil |
Best For Applications |
23-Gauge |
1/2" - 1" |
13 - 25 |
0.76 |
300 |
Micro-pinning, delicate trim, veneers |
18-Gauge |
5/8" - 2" |
16 - 51 |
1.2 |
200 |
Standard trim, baseboards, cabinet assembly |
16-Gauge |
1" - 2-1/2" |
25 - 64 |
1.6 |
150 |
Heavy trim, crown molding, furniture frames |
*Note: All Sinsun brad nails feature electro-galvanized coating and are precision-collated for jam-free performance. Standard angle is 33° for 18G & 16G nails. Custom sizes and coatings are available for OEM projects
brad nails for baseboard
● Our 18-gauge brad nails are perfect for putting up baseboards. Their diamond-shaped tips and 2-inch length let them go through drywall and attach securely to wall posts without hurting fragile MDF baseboards. An Indian contractor said that since switching to our brad nails, the length of their daily installations has gone up by 25%. This is because the nails are neatly arranged and don't get stuck when they are installed quickly.
brad nails for trim
● Use our 15-gauge brad nailsto make sure your door and window frames fit well and look good. Their 1.8mm diameter is a little thicker than that of regular #18 flathead nails, which gives them 30% more grip and keeps your trim strips in place. This cuts down on the need to redo work because of loose trim strips by 90%.
finish nails for nail gun
● Our decorative nails are made for mass production and work well with all pneumatic nail guns. The steel has been heat-treated to a hardness of 48–52 HRC, which keeps it from bending even when driven at hard angles. A Berlin cabinet factory uses 50,000 of these nails every month, and fewer than 0.5% of them jam, so production goes smoothly and without interruption.
Premium Brad Nails for Clean Results
Sinsun brad nails deliver clean, precise fastening for trim, molding, cabinetry, and woodworking projects. Slim profiles minimize surface damage, with corrosion-resistant finishes suited for both indoor and outdoor use.
01
Universal Professional Performance
+
Sinsun 18-gauge straight nails work with all the big brands of nail guns and work perfectly every time. Our precision-aligned nails make sure that your ryobi 18 gauge nailer, DeWalt 18 gauge nailer, or any other electric straight nail gun works smoothly and without any problems. Every shot will be reliable because of the consistent electro-galvanized coating.
Made to work best without cords
+
cordless brad nail systems give you the best efficiency. Our straight nails work with battery-powered trimming nail guns, like the well-known Ryobi Airstrike straight nail gun. The right size and alignment of the nails keep them from getting stuck, so you can finish your projects without any problems.
Works perfectly on all platforms
+
Sinsun straight nails are the most flexible option for professionals who use more than one brand of nail gun. They work very well with all 118 gauge nailer dewalt systems and arrow brad nailer . Because of this, you can use nails from the same brand on all of your tools.
Power Tool Integration That Works
+
Sinsun keeps strict manufacturing tolerances to make sure that all of their power straight nail gun models work perfectly and are compatible with Ryobi nail guns. Our nails feed perfectly, whether you're using a corded or cordless system. This means you'll get the same results every time you use them for decorating and styling.
-
1
Setting Up and Getting Ready for Tools
Start by choosing an 18-gauge finish nailer that works with 2-inch brad nails. To get the best results with white brad nails, make sure your nailer's depth adjustment is set so that there is a 1-2mm recess without dimpling the surface. Load a strip of Sinsun's white brad nails. Their electro-galvanized coating makes them resistant to rust and makes feeding them smooth.
-
2
How to Install
Place nails at 15 to 20 degree angles along trim joints, with 2 inch brad nails spaced 12 to 16 inches apart. The white epoxy coating hides marks well. When these 18-gauge finish nails are set correctly, they only need a little wood filler. The white base layer cuts down on touch-up time by about 40% compared to regular nails on painted surfaces. -
3
Check for Quality and Finish
After getting the materials, check to see if all 18 gauge finish nails are sinking evenly. The 2-inch length gives the best holding power for materials that are 3/4 inch thick. Use matching filler on white brad nails to finish your project. The small recesses in the nails make perfect filling pockets without losing the secure hold.
01020304
Q: What are the real differences between Brads and Nails?
+
A: "Nails" is a broad term, but Sinsun brads are 18-gauge or 16-gauge fasteners with smaller heads that are meant to be less visible. They are the best choice for finishing work where looks are important, unlike bigger common nails that are used for framing.
Q: What sets Sinsun 15 Gauge Nailapart for angled applications?
+
A: Our 15-gauge nails have an angled collation that is made just for angled finish nailers. This design makes it easier to get into tight spaces and holds door and window casings better than straight collated nails.
Q: Do Sinsun Electric Brad Nailers work well with?
+
A: Of course. We make our brad nails with very tight tolerances, which makes them perfect for electric brad nailers. The uniform coating and precise collation keep the machine from jamming, so it works well with both corded and cordless electric models.
Q: Why should you use Sinsun galvanized brad nails for outdoor projects?
+
A: Our hot-dipped galvanized brad nails protect against rust completely, so they can be used for outdoor trim and in damp places. The thick zinc coating keeps rust stains from bleeding through paint, which makes sure that the finish looks professional and lasts.
Q: Where do I usually use Sinsun 1 inch brad nails?
+
A: Our 1-inch brad nails are great for attaching thin moldings, holding cabinet backs in place, and other delicate trim work. The shorter length stops penetration through fragile materials while still providing enough holding power for light uses.
Q: What effect does the brad nail gauge have on my choice of Sinsun products?
+
A: The gauge tells you how thick and strong the nail is. For most trim work, our 18-gauge brads are just right. For heavier moldings, our 16-gauge brads are stronger. Choosing the right gauge makes sure that the material stays in place without damaging it unnecessarily.
Q: How do you use Sinsun brad nails the right way?
+
A: To get the best results with Sinsun brad nails, hold the nailer firmly against the work surface, apply a little pressure, and shoot at a steady angle. Set the depth adjustment so that the nail head is just below the surface without damaging the material.
Q: When should I use Sinsun 16 Gauge Nails instead of other sizes?
+
A: Choose our 16-gauge nails for heavier trim, such as crown molding and baseboards. The 1.6mm diameter gives it 30% more holding power than 18-gauge nails, which keeps heavy trim from coming loose over time while still looking discreet.
Q: Do Arrow nailers work with Sinsun brad nails?
+
Yes, Sinsun brad nails are made to work perfectly with Arrow nailers and other major brands. The consistent collation and electro-galvanized coating make sure that all Arrow brad nailer models work smoothly and without jamming.
Q: What are the differences between Sinsun brads and pins in real life?
+
A: Sinsun brads hold things together much better than pins because they are a little bigger around and have heads. 23-gauge pins are great for small repairs, but our 18-gauge brads are the best choice for most trim work because they hold things together well without being too obvious.
Q: What kind of material is best for Sinsun 1-1/2 inch brad nails?
+
A: Our 1-1/2 inch brad nails work best on materials that are 1/2" to 3/4" thick. This length gives the best holding power for standard trim jobs and stops blow-through on thinner stock, so they can be used for a lot of different projects.
Q: What are the benefits of using Sinsun short brad nails for fine work?
+
A: Sinsun short brad nails (less than 1 inch) let you have precise control when working with delicate wood. Because they are shorter, they are less likely to split thin stock or accidentally go through it. This makes them great for making models and intricate trim.
Q: Is it okay to use Sinsun brad nails in a stapler?
+
A: No, Sinsun brad nails are made just for brad nailers, not staplers. Brad nailers use a different mechanism to drive each nail, while staplers drive wide-crown staples. Using the wrong fasteners can break your tool.
Keep In Touch
TO KNOW MORE ABOUT Sinsun, PLEASE CONTACT US！
We are committed to providing you with the best quality service and look forward to communicating with you to solve problems together and bring you a better experience.
our experts will solve them in no time.